AVS-TX4-3010 Programming

Out of stock
SKU
AVS-TX4-3010 Programming

AVS-TX4-3010 Programming

AVS S-SERIES and A4 S S3/S4/S5 programmable features
Learning waterproof remotes:
1. Disarm the alarm.
2. Turn ignition on.
3. Press and hold lock/unlock button on the original remote (or bottom button on the torch
remote) until the indicators start flashing (and siren chirps if fitted) (approx. four seconds) and
then release the button.
4. Immediately press and hold lock/unlock button on the new remote (or bottom button on the
torch remote) until the indicators stop flashing.
5. Turn the ignition off.
6. The new remote is now coded in.
Learning waterproof remotes when no working remotes are available:
1. Open the driver’s door and then the bonnet.
2. Enter the pin code using the ignition key.
3. As soon as the alarm starts chirping and the lights flash, press and hold the lock/unlock
button on the remote control.
Deleting remotes:
To delete a lost remote a new remote must be coded into the system 12 times. Alternatively the
unit can be sent back to Manta Electronics for resetting.
 
AVS 3010
1. Disarm alarm, open and close door.
2. Within 30 seconds enter the PIN code by turning ignition key from OFF to ACC and back
to OFF (eg turn from OFF to ACC to OFF 5 times for factory set PIN.)
3. Wait 15 seconds, if the PIN was entered correctly the indicators will flash five times to
indicate code learn mode. If not start again from 1.
4. Press button 1 on new remote(s), alarm will chirp once for each remote to be coded in
(maximum of three). NOTE: Any existing remotes will need to be recoded at this
time. Entering Remote programming mode will delete all remotes from system.
5. The system will exit after 20 seconds.
 
AVS 9000
1. Turn the vehicle’s ignition on.
2. Immediately press and hold the bottom button on the original remote until the siren starts to
chirp (approximately four seconds) and then release the button.
3. Immediately press and hold the bottom button on the new remote control for at least four
seconds.
4. Turn the vehicle’s ignition off.
 
AVS 4601
1. Turn ignition on.
2. Immediately press and hold top button on the original remote until the indicators
start flashing (approx. four seconds) and then release the button.
3. Immediately press and hold bottom button on the torch remote (or the lock/unlock
button on the waterproof remote) for at least four seconds.
4. Turn the ignition off.
5. The new remote is now coded in.
To delete a lost remote from the system, the new remote must be coded in 9 times.
This will push the lost remote out of the memory.
 
AVS 5000i
1. Arm then disarm alarm and open and close driver’s door. If the alarm is armed
or immobilised, disarm using the PIN code.
2. Within 30 seconds of disarming turn ignition switch from OFF to ACC and back
20 times, leaving it in OFF position.
3. Wait 30 seconds, if the 20 turns have been entered correctly the indicators will
flash three times to confirm system has entered code learning mode. If it does
not flash start again from 1.
4. Press button 1 of each new transmitter in turn. The system will chirp once to
confirm each transmitter.
5. The system will automatically exit after 20 seconds.
 
NOTE: IF NO VALID REMOTES ARE AVAILABLE AND THE SYSTEM IS ARMED IT
WILL NEED TO BE DISARMED USING THE PIN CODE BEFORE CODING IN NEW
REMOTES.
 
AVS 6000
1. Turn the vehicle’s ignition on.
2. Immediately press and hold the left button on the original remote until the siren
starts to beep (approximately four seconds) and then release the button.
3. Immediately press and hold bottom button on the torch remote (or the lock/unlock
button on the waterproof remote) for at least four seconds.
4. Turn off the ignition.
 
AVS 3000
The AVS 3000 uses fixed code remotes with 50,000 possible codes. The system can
code up to three remotes.
1. Arm then disarm alarm, open and close door.
2. Within 30 seconds turn ignition key from OFF to ACC and back eight times.
3. Wait five seconds, indicators will flash ten times to indicate code learn mode. If
not start again from 1.
4. Press button 1 on new remote(s), alarm will chirp once for each new remote
coded in (max. of three).
5. The system will exit after 20 seconds.
 
AVS 2000
The AVS 2000 uses a factory preset fixed code for the remotes. A maximum of three
remotes can be coded to the system by following this procedure:
1. Disarm alarm (Use PIN override if no remotes are available).
2. Open and close drivers door. (Door input must be hooked up).
3. Within 30 seconds of disarming alarm, turn ignition key from OFF to ACC and
back to OFF five times and leave in OFF position. Wait five seconds.
4. If the number of turns has been entered correctly the system will chirp to
indicate it has entered remote learning mode.
5. Push remote(s) button on new remote. System will chirp to confirm it has
learnt the new remote(s).
6. Repeat for any existing remotes.
7. When the maximum of three remotes have been programmed in or no remote
has been programmed in after 20 seconds the system will exit to disarmed
mode.
 
More Information
Manufacturer .
Button Config NA
Market Any
Copyright © TTK Ltd. All rights reserved.