Daihatsu

View as List Grid

5 Items

per page
Set Descending Direction
  1. DAI-PROX
    DAI-PROX
    Out of stock
    Existing remotes must be re programmed:

    Drops out oldest

    Starting state:

    Doors closed key out of Ignition interior light on auto

    Step 1:
    Open then close the drivers door

    Step 2: Jump 4 and 13 on OBD

    Step 3:
    Turn Ignition on with programmed transponder key

    Step 4: Turn from On to Acc 3x

    Step 5: Locks will cycle

    Step 6: Remove Key from ignition

    Step 7:
    Within 20sec Insert new transponder key

    Step 8: Door locks will cycle.

    Step 9: Remove 4 and 13 jumper

    Notes:
    If you only have an existing Prox, on a purple one use the opposite corner to the buttons or on the black one opposite to the emergency key to be able to turn ignition. A number of the transponders inside the Prox have never been programmed. If this is the case then you will need to Eeprom a transponder Learn More
  2. DAI-REM1
    DAI-REM1
    Out of stock

    Existing remotes must be re programmed:

    Drops out oldest

    Starting state:
    Doors closed key out of Ignition interior light on auto

    Step 1:
    Open then close the drivers door

    Step 2: Jump 4 and 13 on OBD

    Step 3:
    Turn Ignition on with programmed transponder key

    Step 4: Turn from On to Acc 3x

    Step 5: Locks will cycle

    Step 6: Remove Key from ignition

    Step 7:
    Press Lock and unlock together until buzzer beeps 2x

    Step 8: Release then press 1 button

    Step 9: Car will beep again

    Notes:

    Speed! 3 second from Jumping and quickly for 2nd pressAlternate Step 7:Press Lock and unlock together until buzzer beeps 2x Learn More
  3. DAI-REM2
    DAI-REM2
    Out of stock
    Procedure:
    1Ensure all doors are closed.
    2Ensure Ignition is OFF.
    3Disconnect battery negative terminal.
    4Within 15 seconds of disconnecting terminal,connect negative terminal and press remote control LOCK and UNLOCK buttons, or just the UNLOCK button on some models for a minimum of 5 seconds.
    5The vehicle will LOCK and UNLOCK.
    6Then within 5 seconds press the LOCK and UNLOCK buttons, or just the UNLOCK for a minimum of 1 second until vehicle LOCKS and UNLOCKS.

    If programming a second remote control repeat steps 4 to 6.
    NOTE : Maximum of 4 remotes can be programmed.

    Learn More
  4. DAI-Transponder
    DAI-Transponder
    Existing remotes must be re programmed:

    Drops out oldest

    Starting state:

    Doors closed key out of Ignition interior light on auto

    Step 1:
    Open then close the drivers door

    Step 2: Jump 4 and 13 on OBD

    Step 3:
    Turn Ignition on with programmed transponder key

    Step 4: Turn from On to Acc 3x

    Step 5: Locks will cycle

    Step 6: Remove Key from ignition

    Step 7:
    Within 20sec Insert new transponder key

    Step 8: Door locks will cycle.

    Step 9: Remove 4 and 13 jumper

    Notes:
    If you only have an existing Prox, on a purple one use the opposite corner to the buttons or on the black one opposite to the emergency key to be able to turn ignition. A number of the transponders inside the Prox have never been programmed. If this is the case then you will need to Eeprom a transponder Learn More
  5. DAI-VDUMP
    DAI-VDUMP
    Out of stock

    Step 1: Short pins 4-13

    Step 2:
    Put key in and start the vehicle

    Step 3:
    Put 2nd key in and start the vehicle
    Notes:
    4c requires 2 keys and 4d requires 3 Learn More
View as List Grid

5 Items

per page
Set Descending Direction
Copyright © TTK Ltd. All rights reserved.